Alnico Channel Bar Magnets

/Alnico Channel Bar Magnets
  • Alnico Channel Bar Magnets
Primary Competitive Advantages:
  • We are A Professional Permanent Magnets & Magnetic Assemblies Company Operating Since 2004
  • All Magnetic Grade for Sintered & Bonded Magnets
  • Our Quality Guaranteed
  • We Ship Worldwide
  • Small Orders Accepted
  • OEM Design Approvals
  • All Payment Accepted
  • Alnico Channel Bar Magnets, Cast Alnico 5 U-Channel Magnets, Rectangular Alnico Magnet, U-shaped Alnico Magnet Channel Grade5 Casting Channel Magnets, Sintered Alnico Channel Bar Magnet China Factory Manufacturer

    Alnico Channel Bar Magnets  Item No. MPACNL-03 series

    Alnico Channel Grade 5 material, unpainted gray in color and have a maximum temperature of 550 degrees C / Max.Temperature, 1020 °F
    Length tolerance is +/-0.045″, width & channel tolerances are +/- 0.016″ and thickness tolerance is +/-0.005″
    6″ Length, 1” Width, 5/8” Thickness, 3/8” U-Channel Width
    Maximum pull of 40 pounds

    MPCO  Alnico Channel shaped magnets are available in both Cast Alnico 5 and Sintered Alnico 2 materials.
    Very temperature stable, great for high
    heat applications
    Maximum working temperature
    975° -1020°F
    May be ground to size
    Does not lend itself to conventional machining (hard & brittle)
    High residual induction and energy product compared to ceramic. Low coercive force compared to ceramic and rare earth materials (more subject to demagnetization)
    Most common grades of alnico are 5 & 8

    Where Alnico is appropriate, magnet size can be minimized if it can be magnetized after assembly into the magnetic circuit. If used independent of other circuit components, as in security applications, the effective length to diameter ratio (related to the permeance coefficient) must be great enough to cause the magnet to work above the knee in its second quadrant demagnetization curve. For critical applications, Alnico magnets may be calibrated to an established reference flux density value. Cast Alnico 5 Alnico Channel Magnet

    Alnico channel magnets can be used for various holding applications and also for removal of tramp iron from chutes carrying grains, plastics, glass, minerals & other materials conveyed in powder or granular form.
    Alnico channel bar magnets offer high temperature and corrosion resistance as well as greater magnetic pull than ceramic magnets. They are unpainted Gray or Blue in color.

    Alnico channels are magnetized as a horseshoe with the South Pole on one side of the channel & the North Pole on the other side.
    MPCO alnico channel magnets are made of cast Alnico 5 material. All dimensions approximate and as cast with pole faces ground smooth. Other sizes are available upon request.

    ThicknessWidthU-Channel
    Width
    LengthMax.
    Pull, lbs.
    Max.
    Temperature, °F
    GradeItem No.
    3/8“5/8“1/4“5″161020°Alnico 5MPACNL-01
    1/2“3/4“1/4“6″341020°Alnico 5MPACNL-02
    5/8“1″3/8“6″401020°Alnico 5MPACNL-03
    3/4“1 1/4“7/16“6″601020°Alnico 5MPACNL-04
    7/8“1 1/2“1/2“6″601020°Alnico 5MPACNL-05

    All Measurements are in inches (unless otherwise noted). Alnico U-Channel Magnets
    Direction of Magnetization (DOM) is through the thickness unless noted
    Unless otherwise specified, magnets will be furnished in magnetized condition
    Holding forces are approximate. These are average values obtained under laboratory conditions. Size, shape, and material of the test piece may affect actual pull forces

     

    error: Content is protected !!