ELECTRO PERMANENT MAGNETIC BEAM
The electro permanent magnetic beam is the solution for manipulating single steel sheets in various lengths and thicknesses within limited spaces.
PROBLEM DEFINITION
Do you know the problem? Due to lack of space, you are forced to stack steel sheets on top of each other in different lengths. Just imagine, the steel sheets you need are at position 20… This not only costs you time, but also money, a lot of money…
When you organise your steel warehouse with the aid of a telescopic, electro-permanent magnetic beam, you can place the steel sheets right next to each other. The result is a space saving of up to 25%.
Because you can easily pick up sheet by sheet using a magnet, you no longer need wooden beams to be placed between the steel sheets. This also results in considerable space and cost savings.
ELECTRO PERMANENT MAGNETIC BEAM
WORKING METHOD
Simple steel plate treatment in 5 steps:
Position the magnetic beam above the steel sheet and move the electrically driven telescopic arms IN/OFF according to the length of the steel sheet.
Lower the magnetic beam onto the steel sheet and select the number of magnetic modules according to the dimensions of the steel sheet.
Use the 4-position switch to select the right power according to the thickness of the steel sheet.
Carry out the PICK-UP cycle and lift the sheet some 10 cm. Make sure that only one steel sheet is picked up. If several steel plates are picked up, put them down again and reduce the force one position. Carry out the PICK-UP cycle again.
Run the FULLMAG cycle (magnetisation at full power)
You can now safely move the steel sheet.
SAFETY
Electro permanent magnets are the safest solution for lifting single steel sheets. They only require current during the magnetisation and demagnetisation phase. Afterwards, the electric current is no longer required. The effective force is generated by permanent magnets.
For more information on the safety features: click here
ELECTRO PERMANENT MAGNETIC TECHNOLOGY
The electric current is only used to invert the magnetic field, while the effective force is generated by permanent magnets. In the event of a power failure, the magnetic force remains permanently present = 100% safe
SAFETY FACTOR 3:1
To lift safely, a possible air gap between the contact surface of the magnet, and the steel to be lifted, must be considered. That is why all our magnets are designed with a minimum safety factor of 3: 1 measured at an air gap of 0.4 mm.
LANDING DETECTION
An inductive proximity switch and associated cam, mounted on the harp shackle of the hoisting chain, prevents accidental demagnetizing in the air.
RADIO REMOTE CONTROL
The magnet is operated from a safe distance. The operator should not come in the immediate vicinity of the load.
INSTRUCTION PANEL
With clear safety instructions for the user regarding:
– Maximum weight of the load in function of material thickness
– Maximum wing in function of the deflection of the material.
2 BUTTON OPERATION
To start the demagnetization cycle, 2 buttons (SAFE + DEMAG) must be pressed consecutively on the remote control.
LAMP BLOCK
The status of the magnet is visually indicated by a clear LED lamp block. The load may only be moved when the green lamp lights up continuously!
PICK-UP CYCLE
Lifting is done in 2 phases, whereby the workpiece is first lifted at a lower preset force, immediately followed by FULLMAG (100% of the total force)
40mm Education Ferrite Bar Magnets with Red and Blue Poles
Y33 Hard Ferrite Anisotropic Barium Disk Magnet Ø10x4mm
Y30 Hard Ferrite Discmagnet Ø8x2mm
Y30BH Sintered Ferrite Anisotropic Round Magnet Ø10x7mm
Uncoated Disc Magnet Ferrite 10 x 10 mm Y30BH
50mm Painted Ferrite Bar Experiment Magnets with Identified Poles
Ferrite Horseshoe U-Shaped Magnets for Teaching
75mm Blue & Red Painted Bar Permanent Magnet Ferrite for Kids
120mm Ferrite Ceramic Magnetic Bar for Experiments
Diameter 10mm X Width 5mm Ferrite Disc Magnet
Hard Ferrite (Ceramic) Circle Disc Therapy Magnet Ø14x8mm Y30
Y10 Disc Ferrite Magnets with Adhesive Foam Pad D25mmX5mm
